Service Mower OMM142698 Issue I0 Lawn Tractors LT133, LT155 and LT166 PIN (125001 - ) Copyright© Deere & Company Service Mower Removing Mower 1. Park vehicle safely. (See Parking Safely in Safety Section.) Allow engine and muffler to cool completely. C CAUTION: Avoid injury! Rotating blades are dangerous. Before adjusting or servicing mower: Disconnect spark plug wire(s) to prevent engine from starting accidently. Instant download John Deere LT133, LT155 & LT166 Lawn Tractors Service Repair Technical Manual. This manual content all service, repair, maintenance. Page 2, John Deere Model LT155 Lawn Tractor Parts - The serial number is. John Deere Operators Manual - OMM135075 - See product detail for serial. Always wear gloves when handling mower blades or working near blades. Adjust mower cutting height to 25 mm (1 in). Put wood blocks under each side of mower. C CAUTION: Avoid injury! Lift lever is spring-assisted and may have unexpected movement. Put the lift lever in the mowing position before removing or installing the mower. Put lift lever in mowing position, bringing deck down onto blocks. Remove spring locking pin and drilled pin (I) from both rear draft arms (J) and mounting brackets. Move lift lever to the transport position to raise rear draft arms. Remove wood blocks from both sides and slide mower out from under the tractor. Installing Mower 1. Park vehicle safely. (See Parking Safely in Safety Section.) Allow engine and muffler to cool completely. Check that mower cutting height knob is set at 25 mm (1 in). Put lift lever in transport position. C CAUTION: Avoid injury! Rotating blades are dangerous. Before adjusting or servicing mower: Disconnect spark plug wire(s) to prevent engine from starting accidently. The manual steve santagat. The Manual has 643 ratings and 85 reviews. Navessa said: His take. The Manual: A True Bad Boy Explains How Men Think, Date, and Mate. Steve Santagati. May 29, 2007 - Steve Santagati would. A self-confessed serial dater and Bad Boy, Steve is telling all for the benefit of womankind. Every guy is at least part Bad. The Manual: A True Bad Boy Explains How Men Think, Date, and Mate--and What Women Can Do to Come Out on Top [Steve Santagati] on Amazon.com. Santagati, Steve. The manual: a true bad boy explains how men think, date, and mate—and what women can do to come out on top / Steve Santagati. Always wear gloves when handling mower blades or working near blades. Slide mower under the tractor. Put wood blocks under each side of mower deck. C CAUTION: Avoid injury! Lift lever is spring-assisted and may have unexpected movement. Put the lift lever in the mowing position before removing or installing the mower. MIF M88502 15. Check to see if adjustment pin (P) lines up with mower engagement arm hole (O). If pin does not line up, loosen lock nut (Q) and turn pin until pin slips freely into hole. Tighten lock nut. Fasten adjustment pin (P) to mower arm with washer and spring locking pin (M). Replacing Mower Drive Belt (38-Inch Mower) NOTE: In this procedure the mower deck is removed for easier access. However, it is NOT necessary to remove deck when replacing belt. Park tractor safely. Allow engine and muffler to cool completely. Remove mower if desired. Remove self-tapping cap screws (C). Move brake assembly (B) away from sheave (A) and drive belt. Loosen idler (D) and tensioning idler (E) just enough to slip belt past the guides. Remove drive belt and clean top of mower. Install new belt on mower deck as shown. Tighten idler (D) and tensioning idler (E). Align brake assembly (B) with right spindle sheave (A) and fasten with self-tapping cap screws (C). Brake pad must seat against top of sheave. Install mower and adjust mower engagement rod, if necessary. Adjusting Mower Timing Belt Tension (Freedom42) 1. Park machine safely. Move lift lever to mowing position and move to left side of mower. NOTE: Mower timing belt cover can be unfastened and flipped open on the left side, exposing the tension adjustment mechanism, without having to remove the mower or the timing belt cover. IMPORTANT: Avoid damage! Incorrect belt tensioning can cause belt damage. Do not over tighten belt tensioning spring assembly. Loosen jam nut (D) and adjusting nut (E) so that there is a small air gap between washer (F) and mating surface of spring bushing (G). Rotate adjusting nut (E) clockwise until washer (F) makes solid contact with the mating surface of spring bushing (G). Tighten idler assembly center nut (B) to 87 Nm (64 lb-ft.). Tighten jam nut (D) against adjusting nut (E) to 27 Nm (20 lb-ft.). Turn left spindle sprocket (C) to be sure belt is seated properly in the sprockets and idlers. NOTE: The position of the drain holes in the spindle sheave (A) and the indentations in the timing sprocket (M) are in alignment with the mower blades (K) and (L). IMPORTANT: Avoid damage! Damage may occur to the belt or blades after a major blade impact: Check blades for damage and timing. Check the timing belt for damage and proper tensioning. Park machine safely. (See Parking Safely in the Safety Section.) Allow engine and muffler to cool completely. Remove mower. Remove mower drive belt. C CAUTION: Avoid injury! Mower blades are sharp. Always wear gloves when handling mower blades or working near blades. Check blade bolt torque anytime mower is removed. Carefully hold blade with glove, use a hand torque wrench, and tighten bolt to 57 Nm 42 lb-ft.).
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |